This is a demo store. No orders will be fulfilled.

SKU
aMG_P004
In stock
SKU
aMG_P004
฿1,247.66

FiO 2

Overview

     FiO Glide ESP32 is an Internet of Things (IoT) module based on Espressif ESP32-WROVER-IE module, which uses ESP32-D0WD-V3 chip. It has been specifically designed to work with Waijung 2 Blockset, which is an IoT development platform, to design IoT devices with Model-Based Design technique.

FiO Glide ESP32 Key Features

  1. ESP32 Module: ESP32-WROVER-IE
    1. Flash: 16 MB
    2. PSRAM: 8 MB
    3. Antenna: IPEX
    4. WiFi: 802.11 b/g/n (802.11n up to 150 Mbps)
    5. RF frequency: 2412 ~ 2484 MHz
  2. On-board micro SD card slot
  3. On-board 512 kbits EEPROM
  4. Power supply
    1. 5V
    2. 3.3V

    Please Sign in or Create Account before download file

    STM32F417IG Features

    Core: ARM 32-bit Cortex™-M4 CPU with Floating Point Unit, Adaptive real-time accelerator (ART Accelerator™) allowing 0-wait state execution from Flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions

    • Memories
         – Up to 1 Mbyte of Flash memory
         – Up to 192+4 Kbytes of SRAM including 64-Kbyte of CCM (core coupled memory) data RAM
         – Flexible static memory controller supporting Compact Flash, SRAM, PSRAM, NOR and NAND memories
    • LCD parallel interface, 8080/6800 modes
    • Clock, reset and supply management
        – 1.8 V to 3.6 V application supply and I/Os
        – POR, PDR, PVD and BOR
        – 4-to-26 MHz crystal oscillator
        – Internal 16 MHz factory-trimmed RC (1% accuracy)
        – 32 kHz oscillator for RTC with calibration
        – Internal 32 kHz RC with calibration
    • Low power
        – Sleep, Stop and Standby modes
        – VBAT supply for RTC, 20×32 bit backup registers + optional 4 KB backup SRAM
    • 3×12-bit, 2.4 MSPS A/D converters: up to 24 channels and 7.2 MSPS in triple interleaved mode
    • 2×12-bit D/A converters
    • General-purpose DMA: 16-stream DMA controller with FIFOs and burst support
    • Up to 17 timers: up to twelve 16-bit and two 32-bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
    • Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M4 Embedded Trace Macrocell™
    • Up to 140 I/O ports with interrupt capability – Up to 136 fast I/Os up to 84 MHz – Up to 138 5 V-tolerant I/Os
    • Up to 15 communication interfaces
        – Up to 3 × I2C interfaces (SMBus/PMBus)
        – Up to 4 USARTs/2 UARTs (10.5 Mbit/s, ISO 7816 interface, LIN, IrDA, modem control)
        – Up to 3 SPIs (37.5 Mbits/s), 2 with muxed full-duplex I2S to achieve audio class accuracy via internal audio PLL or external clock
        – 2 × CAN interfaces (2.0B Active)
        – SDIO interface
    • Advanced connectivity
        – USB 2.0 full-speed device/host/OTG controller with on-chip PHY
        – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI
    • 8- to 14-bit parallel camera interface up to 54 Mbytes/s
    • Cryptographic acceleration: hardware acceleration for AES 128, 192, 256, Triple DES, HASH (MD5, SHA-1), and HMAC
    • True random number generator
    • CRC calculation unit
    • 96-bit unique ID
    • RTC: subsecond accuracy, hardware calendar

    FiO 2 has been designed to be pin compatible with STM32F4DISCOVERY and fully compatible with aMG F4 Connect 2. If you plan to use FiO 2 without aMG F4 Connect 2, the following picture show minimum required connections.

        1. Connect GND to connector P3, pin
        2. Connect VDD (3.3V @HCLK=168MHz) to connector P3, pin 3.
        3. Connect VREF+ to VDD (3.3V).
        4. Connect VDDA to VDD (3.3V)

    All VDD and GND on FiO 2 are connected together by designed and are intended for better distribution of VDD and GND.

    FiO 2 Connection
    Write Your Own Review
    You're reviewing:FiO 2
    Your Rating